Public speaking pace: words per minute, speed and pauses
Aim for 100 to 165 words per minute when you speak in public. That's the range Microsoft's PowerPoint Speaker Coach recommends for presenters, because most audiences Microsoft tested find it easiest to follow. Until you've measured your own pace, 150 words per minute is a comfortable number to target when working on a script. Reading aloud can run faster than that, and every pause you take lowers your average. These steps work wherever you speak:
- Plan a script at 150 words per minute, then measure your own pace with the speaking speed test.
- Expect a script you read aloud to run faster than speech you make up as you go.
- Take 2.5 words out of your script for each 1-second pause you plan, at 150 words per minute.
- Speak a little slower for an audience listening in a second language, or in a big room.
- Set a teleprompter's speed by ear, and write your pauses into the script.
NinjaPrompter, a teleprompter for iPhone, sets its speed not in words per minute but in points per second, so the last section shows how to match it to your pace and how to write the pauses into the script.
Words per minute for each kind of speaking (and where each figure comes from)
The figure depends on the kind of speaking. Presenters are advised to stay between 100 and 165 words per minute, while adults reading aloud average about 183.
| Kind of speaking | Words per minute | Source |
|---|---|---|
| Presentation | 100 to 165 (recommended) | Microsoft Support, on Speaker Coach |
| Speech in general, US English | about 150 (commonly quoted) | National Center for Voice and Speech, a voice tutorial |
| Reading aloud | about 183 (average across studies) | Brysbaert, 2019, a review of 77 studies of adults reading aloud |
| Audiobook narration | about 155 (9,300 words an hour) | ACX, on audiobook length |
Microsoft's range is a recommendation for presenters, so treat it as a comfortable band to work inside. The 150 is an aside in a voice tutorial, which gives it as the average rate of speech for English speakers in the United States, with no breakdown by setting, so use it as a working number. The 183 comes from adults reading short passages aloud in research studies, in English and several other languages, so it describes reading, which is what you do with a script. ACX says most audiobook narrators narrate about 9,300 words an hour and uses that figure to estimate how long a finished audiobook will be, which works out to 155 words per minute.
That's why 150 is a sensible number to plan with. It's inside the presentation range, it matches the often quoted figure for speech in general, and it's just under the audiobook pace.
Why your pace changes from one talk to the next
Your pace depends on whether you read or speak freely, on the audience, the language, how you feel on the day, and even on the room acoustics.
- Reading or talking. When you make it up as you go, you stop to find the next words, which slows you down. When you read, the words are already in front of you, so your pace tends to rise. That's why a script read aloud usually runs faster than the 150 words per minute in the table above. When reading a speech is a good choice helps you decide whether to read at all.
- Audience. People listening in a second language need more time with each phrase. In one study of English learners, moderately fast speech lowered their comprehension, while slow speech helped them no more than average speech did (Griffiths, 1990). So for a non-native audience like that, it makes sense to keep your pace steady without slowing down too much, but aim to speak somewhat slower than your usual pace in order to not rush. On the other hand, an audience that knows the topic can follow a quicker pace than one hearing it for the first time.
- Room and acoustics. In a large room, with an echo, or without a microphone, slow down a little, because words tend to mash together when you rush.
- Language. Words per minute counts words, and languages build words differently. So compare a count only with scripts in the same language, and don't expect a figure for English to carry over to another language.
- Anxiety. Many speakers speed up when they're nervous, so a pace you measured while relaxed may rise on the day.
- Pauses and reactions. Every pause counts against your average, as the next section shows. At a wedding toast or a eulogy, laughter, applause, or a moment to collect yourself take time too, so write fewer words than the time allows.
Pauses lower your words per minute
Words per minute is words divided by total time, so the seconds you stay silent count against it. At 150 words per minute you say 2.5 words a second, so a 1-second pause takes the time of 2.5 words, and a half-second pause the time of 1.25 words.
Take a 600-word script. At 150 words per minute it takes 4 minutes, or 240 seconds. Add ten 1-second pauses and it takes 250 seconds, so your pace over the whole talk is 600 words in 250 seconds, which is 2.4 words a second, or 144 words per minute. You spoke at 150 the whole time you were speaking, and the ten pauses still took the time of 25 words.
The same sum works backward when you write a script with a goal to fully fill a time slot. A 4-minute slot with ten planned 1-second pauses leaves 230 seconds of speaking, which is 575 words at 150 words per minute. So take 2.5 words out of the script for each second of pause you plan.
Most pauses in read speech are shorter than a second. In a study of people reading short passages aloud in English, the median silent pause was 493 milliseconds, about half a second (Campione and Véronis, 2002). So a full second is a longer stop than most you'd make while reading. How to use pauses in a speech explains why most of your pauses should be short.
Find your own pace (and fit a script to your time)
Time yourself rather than relying on a table. The speaking speed test gives your words per minute for reading a passage aloud, which is the pace a script needs, with any pauses you took included.
Then paste your script into the speech length calculator to see how long it takes at that pace. It also adds the pause marks you type, half a second for each / and one second for each //. Treat the time as an estimate.
If you're starting from a time slot, how many words are in a speech gives the word count, and if you're starting from a word count, how long it takes to read words aloud gives the time.
Set a teleprompter to your pace (and put the pauses in the script)
Set the speed by ear while you say the script aloud. In NinjaPrompter, Scroll speed is in points per second (pt/s), from 10 to 100, not in words per minute, so there's no number to copy over from the speed test. Set the scroll speed to your pace has the method. Your words-per-minute figure still matters for planning, because it tells you how many words fit your time.
Then type the pauses into the script as marks. In Performance mode, the prompter holds the text for half a second at a /, about the length of a typical pause in read speech, and for one second at a //, for a longer stop. [slower] and [faster] slow the text down or speed it up from the tag to the end of the paragraph. Mark pauses, emphasis, and pace covers where to put each mark.
Performance mode is off by default, and it's part of the 7-day trial and the subscription. Showing the marks in your script is free. The holds and pace changes work while the script scrolls on its own.